Huatao Technical News

Why Are Your Screw Flights Coming Out with Uneven Pitch After Forming?

Date Issued:2026-11-18

Uneven pitch can create rework, affect assembly fit and make it difficult to maintain consistent screw flight dimensions. The correct response is not to change machine settings immediately. First determine whether the deviation is present after forming, appears after release, or develops during joining and welding.

Measure Pitch Consistently

Pitch is the axial advance of one full turn. Measure between matching reference points and use the datum stated on the drawing. Check several angular positions around a turn and several turns along the flight. Record the support condition and measurement tool so that results can be compared.

Possible Causes

Blank preparation: incorrect blank dimensions, cut-out profile, thickness or edge condition can affect the formed shape. Compare the blank with the approved drawing before changing the machine.

Tooling and setup: incorrect dies, rolls, guides, mandrels or moulds, as well as wear, damage, poor seating or misalignment, can contribute to pitch variation. Confirm the tooling identity and machine setup.

Material response: material grade, hardness, thickness and batch variation can change forming behavior. Springback may alter the released geometry. Compare measurements before and after release and record the material batch.

Forming progression: depending on the equipment, inconsistent blank seating, feed slippage, strip tracking, guide alignment or operator sequence may affect the result. Troubleshooting must match the actual machine design.

Welding and assembly: if pitch is correct before welding, check shaft alignment, joint fit-up, fixtures, heat input and weld sequence. Measure before and after welding to identify whether the change is downstream of forming.

Match the Equipment to the Process

Sectional hydraulic forming, continuous cold rolling and mould winding are separate processes. For individual plate segments, review the Spiral Blade Forming Machine. For strip-based continuous flighting, review the Continuous Screw Flight Cold Rolling Machine. For a winding process, see the Winding Spiral Blade Forming Machine. The tooling and setup checks must be specific to the machine being used.

A Practical Quality-Control Routine

Verify the drawing revision, datum and tolerance.

Measure blank or strip dimensions before forming.

Record the machine configuration and tooling ID.

Measure the flight immediately after forming and after release.

Inspect several consecutive parts, not just one sample.

Record changes after segment joining or shaft welding.

Document any approved corrective action and repeat the test.

When a Supplier Review Is Needed

A supplier's review should begin with the complete part definition rather than a single pitch value. OD, ID, pitch, thickness, flight hand, material grade, blank or strip form and finished length interact during forming. If only one dimension is supplied, the supplier may not be able to distinguish a tooling mismatch from a geometry or material issue. Include the current drawing revision and identify which dimensions are critical to fit and operation.

For repeat production, ask how the proposed machine setup is documented and how tooling changes are controlled. Clarify which settings are operator-adjustable, which require a different tool and which must only be changed by service personnel. A good technical evaluation should also establish how the supplier will verify the result: sample material, number of test pieces, measurement locations, inspection instruments and acceptance criteria.

Do not compare machines using a single advertised maximum diameter or thickness. Confirm the combined working range for the required material, pitch, OD, ID and thickness. Ask whether the stated capability is based on a tested sample, a standard configuration or an optional tooling package. If the machine is expected to produce both sectional and continuous flights, verify whether separate equipment routes are needed rather than assuming one forming mechanism covers both.

If the pitch remains inconsistent after input, tooling and setup checks, provide the supplier with the finished drawing, blank drawing, material grade, thickness, machine model, tooling ID, setup record and measured defect pattern. Include photos only as supporting evidence; dimensional data and process timing are essential. A representative trial should use the intended material and agreed acceptance criteria.

For screws used in plug-feeding systems, the finished flight also needs to match the shaft and assembly interface. Review the Plug Screw Feeder Shaft in the context of the complete screw assembly and its drawing; this is an application/assembly reference, not a forming-machine troubleshooting substitute.

Conclusion

Reliable pitch control starts with a reliable datum and a stage-by-stage inspection. Confirm the blank, material, tooling and machine setup, then check for springback and downstream welding distortion. Use controlled trials and production records to verify repeatability across the required product range.

Contact HUATAO

Email: Lucy.chai@huataogroup.com

Tel / WhatsApp / WeChat: +86 153 7388 3537

WhatsApp: https://wa.me/15373883537

Website: https://www.refinerdisc.com/

Contact page: Contact HUATAO

* E-mail :

can not be empty

* Question :

can not be empty

Related News